How Much Power Can The BMW N55 Handle?

How much power can the stock N55 engine handle? What are the limits on the BMW N55 block, rods, pistons, crank, etc? These are common questions in the aftermarket world, but there is never a perfect answer. However, there are some general safe limits for the N55 engine. In this article, we lay out the N55 engine limits in a straight-forward way. We also dive into a deeper analysis of BMW N55 strength and limits.

**Note - this article is in reference to the standard N55 and does not directly apply to the stronger N55TU found in the M2 and X4 M40i.

Modded N55Pin

N55 Engine Limits - Quick Answer

The N55 can handle around 550whp and 550wtq on the stock engine block and internals. Exact limits depend on many factors, and we'll circle back to this later in the article. For now, we're sticking with the simple answer. However, this next paragraph is very important.

Any power limits we discuss in this article are estimates. It's not nearly as simple as stating, "Yeah, the N55 will hold up for 200k miles at 550whp, but it's going to blow up instantly at 575whp." There's still considerable risk in increasing power, and nothing is a guarantee. Nonetheless, the general rule applies. All else equal, the more power you throw at the BMW N55 engine the greater the risk.

Stock N55 Rods, Bearings, Pistons (550-600whp)

These are often the first parts to let go on the N55. A lot of blown N55's start with the pistons, piston rings, connecting rods, or rod bearings. The N55 took a small step down in strength compared to the older N54. It's still a fairly strong motor, but seems a little less tolerant to abuse. A bad pre-detonation at 500+whp can quickly bend a rod.

Those same pre-detonations may also crack a piston. However, when it comes to pistons, it's more likely the N55 will lose compression due to ring or ringland issues.

Rod bearing problems are a hot topic for the N55 engine. Keep in mind - the internet can quickly blow things out of proportion. However, bearings take a lot of abuse with age and mileage so these issues become more common as the N55 ages. High quality oils and timely oil changes are one of the keys to ensuring healthy rod bearings. Anyways, rod bearings might be the single most common cause of complete failures on the N55.

N55 Stock Engine Block Limits (700-800whp)

Engine blocks on the N55 are an interesting discussion. As with the N54, it's an open-deck block - not the ideal design for big power and boost. Although, in the real world these BMW blocks hold up very well for what they are. We suspect the N55 block should hold up pretty well even at 700whp.

Problem is - not many, if any, N55's have been pushed to 700+whp. As such, the exact limits are still up in the air. We do know the N54 block holds up well at 700-800whp, and the N55 would likely accomplish the same.

*Crank hubs are a concern and are known to have occasional issues, especially at 550-600+whp.

Stock N55 Crankshaft (700+whp)

N55 cranks are a tough one. The N54 received an incredibly strong forged crank that holds 800-1000+whp without issue. However, N55 engines receive a standard cast crank. Some claim to have already run into crankshaft issues on the N55. None of the cases seem power related, and we would question whether or not the cranks were even to blame for the failures.

Anyways, there just isn't enough data to know exactly what the N55 crank is capable of. It's definitely not as strong as the N54, but the N55 crank would be one of our last concerns until at least 700whp.

N55 Cylinder Head Limits (700+whp)

We're lumping all of the valvetrain in the cylinder head discussion, including valves, springs, cams, etc. These are highly capable parts on the N55 that will support 700+whp. Random failures can and do happen, but it's not common even at high power.

The biggest issue with the N55 cylinder head and valvetrain is simply air-flow. Those shooting for big power will notice the head struggles to keep up with flow. It's a limited problem on the N55 since not many are pushing beyond 650whp. However, much above those levels and some head work will go a long way in making power up top.

Deeper Review of N55 Power Limits

Finally, we're circling back to one of our early comments. There are tons of factors that determine how much power each N55 can actually handle. What are those factors? How can you reduce the risk of blowing up the N55? We will break this discussion into the following topics:

  • Power & torque
  • Turbo choice
  • Maintenance
  • Tuning & supporting mods
  • Data-logging

It's not an exhaustive list. However, the above are a few of the factors we can control. Some external factors are simply out of our control, and that's just part of accepting the risk in pushing the N55 power limits. Luck of the draw can play a role. Flukey failures happen. The list goes on.

Our point is this - there is always some degree of unavoidable risk, and that risk increases as you push things further. Regardless, it's important to reduce the risk with a proper setup. Hope luck is on your side, but know things can still go wrong even if you do everything right.

N55 Horsepower vs Torque

When discussing the upper "safe" limits of any engine torque is actually the better number to look at. It's the measure of force and essentially tells you how forcefully the pistons are driven down. Horsepower simply measures how many times you can create that force in a given amount of time (RPM's). The equation is as follows:

HP = Torque x RPM / 5252

Shifting the power curve to the right allows you to make more power with less torque (less force). Here's are some quick examples:

  • 550wtq x 5000 RPMs / 5252 = 523whp
  • 550wtq x 6000 RPMs / 5252 = 628whp

Both are subjecting the internals to the same force, but shifting the curve right allows an increase of over 100whp. It's a lot easier to make a given amount of power at higher RPM's.

N55 Turbo Setup

The turbo setup ties into the above discussion with shifting the power curve right. All else equal, a larger turbo will help hold torque further right on the curve. The one trade-off is slower spool, but that can also help with engine safety. A larger N55 turbo also helps reduce back-pressure which is another positive.

We'll avoid getting too technical and writing on and on about this. Point is - a larger turbo is generally safer for the N55 engine at a given power level.

BMW N55 Maintenance

Alright, this one is pretty obvious. Stay on top of N55 maintenance. Stick with high quality oils, and you may even considering using racing oils. An oil change interval of 3,000 to 5,000 miles is also a good idea.

When problems occur then fix them in a timely manner. Turn boost down until your N55 is fixed and running well. Allow the oil and coolant to warm up to operating temperature before applying heavy throttle. If things get too hot then give the N55 a gentle cool down cruise.

It's basic stuff that's a good idea regardless of your N55's power. However, it becomes more and more important as you begin pushing things toward the N55 power limits.

N55 Tuning & Mods

Tuning and supporting mods are one of the most important topics. Stick to the conservative side of things. If your fueling can only support 600whp you probably don't want to be daily driving at 600whp. Build in some headroom. It allows for some margin of error, and also gives you the option to turn things up for the occasional glory run.

On the tuning side - go conservative with that too. Ensure you're running the proper fueling. Which speaking of, E85 and/or methanol injection are not only needed to push the limits but it's also imperative to have proper fueling. Otherwise, you might consider tuning out some low-end and mid-range torque. We could go on and on. Ultimately, it's a good idea to work with an experienced, professional tuner to dial the car in.

N55 Data-Logging

Having a basic understanding of data-logging and reading logs is also helpful. You want to keep an eye on the engine parameters often. When pushing the N55 limits a small issue can turn into a major one. You should know everything that's going on with your N55.

Look for lean AFR's, maxed fuel trims, timing pulls, etc. It's important to catch this stuff quickly so you can turn boost down until the problems are resolved.

BMW N55 Engine Strength Summary

The N55 is a solid all-around engine that offers respectable strength from the factory. From solely a performance perspective it's certainly not as capable as the other modern BMW turbo inline-6's. However, the N55 can still handle about 550-600whp with a proper setup.

Rods, pistons, and bearings are a few areas that will first cause trouble. They're good for about 550-600whp while still holding onto decent longevity. The block, cylinder head, and crank should all hold a bit north of 700whp. However, there just aren't enough N55's making that power to have any solid evidence.

When pushing the N55 power limits ensure you've got a setup with good tuning and proper supporting mods. Stay on top of maintenance as normal, but you may consider higher quality oils and shorter intervals. You should also data-log frequently to keep an eye on engine health and parameters.

What's your experience with high horsepower N55 engines? Drop a comment and let us know!

Categories:

Share your thoughts

Your email address will not be published. Required fields are marked*

4 thoughts shared

  1. Comment author image

    Anderson Lebler

    says:

    Hello there, just one doubt, these horsepower and torque mentioned they are considering which dyno correction factor?

    great article by the way 🙂

  2. Good info. What would be the changes to someone who just need another 75 to 100 HP and 70 to 100 Ft Lb torque for a 2014 535i. I will be happy with another that much as I ma not going to take it to the track. I just need some more power to keep up with the new powerful cars. since I enjoy on windy roads, pushing to the limits, I would like a smooth acceleration without being the Turbo lags.

    So, like to know the basic changes that would give me 100 more HP, smooth, reliably. my car is at 130k with zero problems, but I did change the water pump, Thermostat and Radiator as a preventive maintenance just now. Thanks

    1. Hi Michael,

      We wrote an article about basic N55 bolt-on mods here. Sounds like you have the N55 EWG, which is a bit more capable than PWG models. A tune, intake, and downpipes should help gain about 50-75whp. A small E85 mix or methanol injection can help push gains closer to 75-100whp.

      An FMIC is also a great mod that you might find a lot of joy in. It’s not going to gain much peak horsepower on glory runs. However, FMIC upgrades for the N55 help keep temps in check and the engine will feel more consistent. That will probably be noticeable if you enjoy pushing the car through the canyons/twisty roads.

      Sounds like you knocked out some good preventative maintenance. Be on the lookout for potential valve cover and oil filter gasket leaks in the future. Those are a few known issues that are pretty common with age and mileage. Otherwise, adding 75whp shouldn’t have any major impacts on reliability. It will add some stress, of course. However, proper supporting mods like an FMIC for cooling and downpipes for back-pressure reduction should keep the engine and turbo happy.

      Best Regards,
      Zach